Equipment & Suggested Price 2004*
Maxi 1200
Volvo Penta Power MSRP
D2-55 (Diesel) 55hp (39kW) $374,936
Standard Equipment
Hull  
White, high-temperature NGA gelcoat is sprayed up in the moulds. The hull is laid up by a 
combination of hand lay-up and spraylay-up in a female mould. The laminate is then hand 
consolidated. The hull is partially laminated in isopolyester, partially in 
DCPDOrthopolyester. A sandwich laminate made of 20mm PVC core is used on the 
topsides above the turn of the bilges. Chopped strand mat is used as reinforcement with 
woven roving in the centerline. The keel area is a solid laminate as well as the 
laminate around major through hull fittings. Smaller through hulls have the edges of the 
sandwich treated with a sealer. White topcoat on the hull in all lockers, bilges and similar 
exposed areas. Striping with blue vinyl tape. Hull color, white or blue.
Internal Reinforcements  
Female molded hull stiffening and inner liner grid. Grid molded in white gelcoat and 
DCPD-ortho polyester using tri-axial and uni-directional glass in top hat sections. Forward 
and aft the grid is glued to the hull using polyester putty Prestocol TH 725 A or similar. In 
the keel area the grid is hand laminated to hull. A structural ring frame incorporating 
marine plywood bulkheads, multiple hand laminated shelves and top hat stiffeners 
distribute the load from shrouds. The grid is prepared with hose and cable runs. Structural 
marine plywood bulkheads are glued, bolted and/or laminated to the hull. All marine 
plywood is Water and Boil Proof in compliance with British Standard 1088.
Keel  
1.75m draft lead antimony 2.5% casting with incorporated bulb. Low centre of gravity. 
Keel is bolted with 9xM20 AISI 316L stainless steel bolts. 10mm keel washers in stainless 
steel.
Rudder & Tiller Steering  
Hand laminated rudder blade using white gelcoat and bi-axial and uni-directional E-Glass 
reinforcement in a polyester resin. φ79mm aluminum AISI 6082 rudder stock with three 
wings welded to the stock. The wings of the stock are laminated to one half of the rudder 
before assembly. The blade halves are laminated and glued together. The top and bottom 
bearing is a acetal needle bearing for minimum resistance and maintenance of the 
balanced rudder design. Lewmar Constellation wire steering with an aluminum
alloy 12” 80º quadrant. φ1016mm stainless steel single spoke steering wheel with leather 
cover. Emergency tiller.
Deck  
White, high-temperature NGA gelcoat is sprayed up in the moulds. The deck is laid up by 
hand and by spray lay-up in a female mould with integrated antislip surfaces. The deck is 
laminated in DCPD-Ortho polyester. A sandwich laminate made of 15mm PVC core is used 
in all horizontal surfaces. Chopped strand mat is used around recesses for hatches. All 
fittings are fixed in either single laminates or a sandwich with a marine plywood or 
aluminum core. The deck is glued to the hull using polyester putty, and subsequently 
bolted using M8 bolts c-c 200mm.The deck includes grooves and platforms for hatches and 
lids. Striping with blue vinyl tape. White topcoat in all exposed areas. Glove box with 
teak frame on port and starboard.
Teak deck included. Teak in cockpit and on swim platform.
Deck Equipment for Sail Handling  
2x halyard winches Lewmar 16CST Chrome; 2x primary winch Lewmar 48CST Chrome
2x mainsheet winch Lewmar 30CST Chrome
1x mainsheet track Lewmar Sz2 Ocean; 2x genoa track Lewmar Ocean Sz 2, L=2920mm
4x clutch Lewmar double 10-12mm; 1x clutch Lewmar single 10-12mm
1x clutch Lewmar single 6-8mm; 2x organizer Lewmar 4-sheaves acetal
2x foot blocks Lewmar double 80mm; 2x large padeyes mainsheet
2x genoa car Lewmar Ocean Sz 2; 1x mainsheet car Lewmar Ocean Sz 2
2x camcleat Servocleat Sz 1; 4x block Lewmar Sz 1
6x block Lewmar Sz 2; 1x block Lewmar Sz 3
2x winch handle Lewmar 12”; 2x winch handle Lewmar 10”
Ventilation, Windows, Skylight and Portlights  
Skylight stainless steel frame 20”x20” 1x forward cabin
Skylight stainless steel frame 20”x20” 1x saloon
Skylight stainless steel frame 20”x20” 1x owners cabin
Skylight stainless steel frame 10”x20” 1x owners cabin
Portlight, stainless steel frame, opening 2x toilet, 3x galley, 1 owners cabin
Stainless steel framed acrylic windows 4x saloon, 2x owners cabin
Dorade ventilators 2x owners cabin, 2x saloon
Hatches & Lids  
Teak doors in companionway. Teak sliding hatch cover with wooden trims for storage.
GRP molded hatches on deck: 2x anchor well forward
(All hatches in sandwich laminate) 1x anchor well aft
1x side deck storage port
1x LPG locker
1x companionway sliding hatch, 10mm acrylic
Other Deck Gear  
Windscreen with stainless steel frame and glass windows. Handle on windscreen frame in 
cockpit. Sprayhood; blue canvas with stainless steel tubing. Teak foot rail without holes. 
Teak rubbing strake with stainless steel chafe protection. 2x 4mm lifelines 600mm above 
deck. Swaged terminals. 6x stanchions. Guard wire gate in stern. Guard wire gate on port 
and starboard side decks. Compass, Silva on top of steering pedestal. Flagpole 
900x25mm. Teak at port pushpit. 4x halyard bags (supplied loose),
Stainless Steel Deck Gear  
All AISI 316L acid proof steels. Hand polished.
Pulpit 25mm 1x Bow
Pushpit 25mm with teak seat 1x SB stern
1x Port stern
1x Stern fender stand
Bowsprit with stanchion support and bow rollers
Chain plates 1x Forestay
1x SB shroud
1x Port shroud
Handrail, 25mm 2x cabin rooftop
Bathing ladder Bathing platform through bolted in anchor well aft.
Mooring Cleats 6x 265x70
Mooring rope chafe protection 2x (side cleats)
Backstay attachment
Helm seat handhold
Protective cage over cowl ventilators, 25mm 2x owners cabin rooftop
Handle on outside of windscreen 1x port & 1x starboard
Interior   
Interior in mahogany covered with 3 layers of varnish to a satin finish. Acid curing semi-
gloss alkyd varnish. All cushions in suede velour fabrics. All doors and drawers have push-
Saloon & Navigation  
Seat cushions and backrest cushions. Saloon table with storage in central box with lid. 3x 
louvered doors over lockers. 2x bookshelves in front of chain plate boxes. Hull cladding in 
ribbed mahogany. Curtains fitted in covered tracks. Substantial handhold on port. 
Detachable panels in ceiling. Solid mahogany mast pillar. Access to storage below seat 
cushions. Carpet on luan wooden floor. Chart table with wooden trims all around. Storage 
under nav seat. Electrical panel on hinged door. Standing headroom 1.97m. Optional full 
length berth on port in saloon. Nav. table then removed.
Galley  
Laminate countertop in cream color. Wood trim on countertop outer edge. Stainless steel 
double sink. Oiled teak floor. Top loaded fridge Waeco 100L with compressor. 4x louvered 
doors above countertop. 4x drawers. Round cabinet with two shelves on end of galley 
counter. Waste bucket under sink. Handholds in companionway. Stainless steel 
companionway ladder with teak steps. 1x hatch below stove. 1x hatch outside of stove. 1x 
top loaded locker in counter. Access to compressor & diesel tank through louvered locker 
door. Cutting board. Standing headroom 2m.
Forward Cabin  
2x sleeping cushions. Hull cladding in ribbed mahogany. Blind for skylight 600x600mm. 
Ceiling made of detachable panels. 4x lockers and 2x bookshelves above berths.. 1x large 
hanging locker and 1x shelved locker. Standing headroom 1.85m. Sliding door into saloon. 
Mirror forward with wooden frame. Storage under berth.
Owner's Cabin  
3x sleeping cushions. Double berth on port. Single berth or large seat on starboard. Hull 
cladding in ribbed mahogany. Blind for skylight 24”x24”. Ceiling made of detachable 
panels. Overhead lockers with 2x louvered doors and bookshelf. 2x drawers in
cabinet aft. Hanging lockers port and starboard. 2x drawers under berth on port. Storage 
aft of engine room. Mirror with wooden frame. 2x curtain on aluminum pipes. Doors for 
easy access into engine-room. Standing headroom 1,75m.
Heads  
Shower sump discharge pump SWN 1100-12V. Separate shower. Stainless steel sink with 
discharge. Toilet paper holder behind locker door. 2x hooks for clothing. 2x mugs with 
holder. Mirror sliding doors above toilet counter top. Stainless steel handholds.
Mirror with wooden frame. Shower teak grating. Toilet brush. Shower curtain. Standing 
headroom 1.95m
Machinery  
Aft of the heads a dedicated space for installing optional yacht systems like heater and 
battery charger is allocated.
Cockpit  
Rigid teak cockpit table.
Mast & Rigging  
Mast is fractionally rigged with a deck stepped mast base. Seldén 235x116mm mast 
section made of silver anodized aluminum. In mast furling is standard. Double set of 
spreaders.
Boom  
Silver anodized aluminum alloy boom section 171x94mm. Internal outhaul.
Standing Rigging  
Discontinuous stainless steel 1x19 strands wire-rigging. Stud-toggle rigging screws.
Forestay, FURLEX 208 8mm Intermediate shroud, Terminal <> stud 7mm
Upper Cap shroud, eye <> eye 8mm Lower cap shroud, fork <> eye 10mm
Permanent backstay, eye <> eye 6mm Aft lower shroud, eye <> eye 10mm
Mechanical backstay tensioner from Hasselfors.
BOOM VANG Seldén rod kicker Type 20.
SAILS All sails by ElvströmSobstad Sails.
Mainsail. 31m2. Crosscut dacron. Leech line. Loose footed. Prepared for Seldén Furlin´. 
Sail numbers, class mark, tell tales on
leech. Sail bag.
Genoa 37m2. Crosscut dacron. Sail is prepared for Furlex. Tell-tales. Sail bag.
Engine & System  
All through hull fittings close to the waterline and below have shut-off ball valves. All hoses 
are attached to through hulls with double stainless steel hose clamps.
Engine  
A four-cylinder Volvo Penta D2-55 engine with a MS25S sail drive. Fresh water cooled. 
Teleflex Morse engine controls. VolvoPenta fuel filter. Volvo Penta muffler. Well 
soundproofed engine room. Folding 3-blade propeller. Engine panel.
Fuel System  
Fuel tank 200 L. Stainless steel. Inspection hatch in tank. Fuel feed and return hose with 
shut-off valves. Fuel feed for diesel heater. 38mm fill hose. 19mm ventilation hose. Fuel 
level indicator on navpanel.
LPG System  
2-burner LPG stove, gimballed. 3kg LPG bottle with ventilated storage on bathing platform. 
Pressure reduction valve 30mBar. Shut-off valve at stove. Continuous copper pipe 8x1mm 
from bottle to stove. 400mm LPG hose at bottle. 1000mm LPG hose at stove. Swaged 
terminals on LPG hoses.
Bilge Water System  
Electrical bilge pump SWN1100-12V in heads Suction point at keel sump Discharge below 
Sheer line Manual bilge pump 1 1/2” in owners cabin Suction point at keel sump Discharge 
below sheer line Manual bilge pump 1 1/2” cockpit Suction point in engine room Discharge 
below sheer line
Freshwater  
Tanks stainless steel 250L + 110L. Water level indicator on nav. panel. Suction from 
tanktop to avoid leakage. Hot water calorifier22L. Pressurized freshwater pump WPS 3.4-
12V. Single lever tap in galley. Single lever tap in heads. Shower in heads. Shower
on bathing platform
Head System  
Toilet bowl. Manual pump. Stainless steel septic tank 80L. Discharge overboard 50mm. 
Deck suction point 38mm. Ventilation hose. Vacuum valve for toilet seawater intake. 
Sanitary hose
Navigation and Interior Lights  
All navigation lights comply with COLREG 1972.
Navlight 1x Lantern stern, white 1x Lantern bow, red&green 1x Lantern mast, white
Reading lamp, chrome 4x saloon 4x owners cabin 2x forward cabin
Reading lamp, black flexible 1x nav table
Ceiling light 3x saloon 1x forward cabin 4x galley 2x owners cabin
Electrical System  
12 volt electrical system. The main cable runs are placed in ease accessed channels.
The battery bank contain: 1x starting battery 75Ah
5x service battery 75Ah
Electrical Switch Panel
Circuit breakers :
Nav Lights Steaming Light Deck Light Anchor Light 3-colour light VHF/Radio Autopilot
Instr/Clock Radar/Instr Heater Control Heater Fan
AUX AUX FW pump Bilge pump Shower pump Refridge Engine fan
Interior Light 1 Interior Light 2 Interior Light 3 Power
Level gauges:
Fuel Level Water Level Voltmeter
12V socket 1x switch panel 1x heads 1x cockpit
Main fuse panel placed at companionway.
Fuse Groups Radio/Mem Clock Heater Bilge Pump
Main Switches Engine Aux
Battery charging by 60Amp generator on the engine. Volvo Penta electronic battery 
charging regulator.
Depth Raymarine ST 60
Speed Raymarine ST 60
Delivery  
4 x mooring rope. 4x fenders & fender socks Decal for lifting slings
Toolbag Boat hook, telescopic Brush with telescopic handle
Document Bag containing complete set of instruction manuals. Maxi Yachts Service
Transport Cradle (Maxi 1200, Normal Keel)
Transport/Storage Protection Cover
Safety  
2x Fire extinguisher 2 kg powder. Fire-port for engine room.
Optional
Optional Equipment Price
Anchor Winch (Electric) on Bow, Lewmar 1000W (1050 incl. Anchor Roll) $3,680
Anchor Winch (Electric) on Bathing Platform $4,979
Anti-fouling $2,181
Autopilot, Smartpilot S2 ST6001 STD $6,312
Barometer & Clock, Chrome $460
Bedset for 4 Persons $1,100
Bow Thruster, SP 7.5 incl. Gen. + Extra Batteries $6,594
Cockpit Cushions $700
Cooker with Oven & Grill; Add $460
Commission, Launch and Rigging $2,523
DVD Player $860
Gennaker, Full Radial $3,639
Gennaker Equipment $1,581
Furlin Genoa, Offshore Tri-optimal Sandwich incl. UV-Protection $2,500
GPS Raynav 300 incl. Antenna $1,560
Heater, Ardic (for M1050: Ebersprächer Air Heater) $3,958
Furlin Main, Offshore Sandwich Trioptimal, 4 Vertical Battens $2,041
Multirepeater Raymarine ST60 $960
Plotter Raymarine SL530 7" Color Screen at Pedestal, incl. RS120 Antenna $5,577
Radar/Plotter Raymarine SL70CRC 7" Color Screen at Pedestal, incl. Antenna 1) $10,619
Radio / CD incl. 2 Speakers in Saloon & 2 in Cockpit $1,359
Self-Tacking Jib, Tri-optimal Sandwich 21,5m2 incl. Complete Track; Add $4,205
Shore Power 120V or 240V incl. Battery Charger 25A $2,280
Spinnaker, All Purpose $4,609
Spinnaker Boom Cruising incl. Sheets, Guys and Blocks $2,100
Spinnaker Sock $820
Sprayhood Extension $2,210
Steering Pedestal Cover $280
Transport Factory Visby-Gothenburg $3,630
Transport Factory Visby-Sthlm $2,726
TV 10,4" LCD incl Mast Top Antenna $1,839
VHF Ray 230E TFM incl. Antenna $3,519
VHF Ray 230E TFM; Add for 2nd Hand Unit $859
Wind Instruments, Raymarine ST 60 $1,600
1) Requires optional Autopilot Compass Based on Gyro
All sails by Elvström/Sobstad
Prices for mainsails and jibs/genoas are additional prices over standard sails.
Prices for extra equipment are only valid if ordered before building of the boat has started.
* Prices are based on MSRP and are in U.S. dollars. Prices are  
   subject to change and retailers price may vary.
   
Phone: +1.469.358.2236 or +1.214.680.0185
e-mail: info@swemarine.com    www.swemarine.com